Search Results:
Search Results:
Search Results:
Search Results:
Brass pin clips fix suitable round electrical cables to timber surfaces. They keep the cable supported, neat, and protected from movement during and after installation. Licensed electricians, sole traders, maintenance contractors, and informed retail buyers all use them in residential and light commercial work. Trade buyers favour them for visible runs on exposed timber, where appearance and corrosion resistance both matter.
A brass pin clip has three parts: a looped brass body, an integral steel pin, and a small retaining tab. The loop wraps around the cable. The pin drives into the timber. The tab holds the cable in position once the clip is set. The clip supports the cable against the timber surface. It does not replace cable containment, conduit, or mechanical protection where those are required.
The pin secures the clip to the timber substrate. The brass loop holds the cable in line with the planned route. This reduces sagging, controls cable routing, and limits rubbing or shifting against framing edges. Final installation must follow the manufacturer instructions and AS/NZS 3000 cable support requirements. Spacing, fastening method, and cable selection are job-specific decisions for the licensed electrician.
Common applications include timber joists, rafters, ceiling spaces, sub-floors, skirting boards, architraves, and exposed timber framing. Electricians use them during residential rough-ins, light commercial work, renovation repairs, and neat visible cable runs. Suitability depends on the cable type, the surface, the environment, and the relevant electrical compliance requirements for the installation.
The primary buyers are licensed Australian electricians, sole traders, maintenance contractors, and small electrical businesses. Informed DIY and retail buyers also purchase brass pin clips, often as parts for a job their licensed electrician will complete. Electrical wiring work must be carried out by a licensed electrician where required by Australian law.
The Clipsal 564PC range is the standard reference point for brass pin clips in Australia. It covers five sizes that suit most common round cables used in residential and light commercial electrical work. Choose the correct size for the cable, not the cable rating.
The five Clipsal 564PC sizes are listed below. Match clip size to the cable circumference and the practical fit, not the cable current rating.
| Clipsal Size | Approximate Cable Diameter Suited | Typical Use |
|---|---|---|
| Size 1 (38 mm clip) | Smaller round cables | Light flexible cables on timber |
| Size 2 (44 mm clip) | Small round cables | Common rough-in cable runs |
| Size 3 (51 mm clip) | Mid-sized round cables | General timber-fixed cable work |
| Size 4 (57 mm clip) | Larger round cables | Heavier rough-in and feeder runs |
| Size 5 (67 mm clip) | Largest round cables in the range | Larger flexible round cables |
Cable diameter varies between manufacturers and constructions. Always check the actual cable before ordering clip size for a job.
Cable outer diameter and circumference vary by manufacturer and cable construction. Measure the cable, or check the manufacturer data sheet, before selecting a clip size. Undersized clips can compress the insulation and cause damage. Oversized clips allow movement, which defeats the purpose of fixing the cable.
The clip should fit snugly around the cable. The cable should not slide freely once the clip is set, and the brass loop should not crush or deform the insulation. If the fit feels wrong, step up or down a size before installation.
Common Clipsal 564PC brass pin clips are supplied in packs of 200. Trade buyers often carry several sizes in service vehicles and job boxes. Stocking multiple sizes reduces rough-in delays, avoids substitution errors, and limits return trips for missing parts. The pack quantity also suits regular maintenance work and recurring residential jobs.
Brass construction gives the clip good corrosion resistance and a low-profile finish. Brass does not become brittle in the same way as some plastic clips when exposed to heat or sunlight. The product is suited to sheltered damp environments where a corrosion-resistant fixing is required. Avoid treating brass pin clips as fully weatherproof in fully exposed or marine conditions.
Brass pin clips remain a common choice in Australian electrical work for practical reasons: durability, cable support quality, neat appearance, broad availability, and good value at trade pack quantities. They are a specific solution for round cable on timber, not a universal cable fixing.
Brass resists rust and performs well in many damp, roof-void, sub-floor, coastal-adjacent, and sheltered outdoor environments. It is corrosion resistant, not weatherproof. Direct marine exposure, harsh chemical environments, or fully exposed outdoor conditions can require stainless steel saddles, stainless cable ties, or another compliant fixing method. Match the fixing material to the actual exposure category for the job.
Brass does not become brittle in the same way as some plastic clips, especially in heated roof spaces. Service life depends on correct sizing, sound timber, an appropriate environment, and compliant installation. A clip that has been removed, bent, or damaged should generally be replaced rather than reused. Reused clips lose grip on the cable, and a damaged pin can split the timber or fail to seat properly.
"Best" in trade terms means the right size range for the cables on the job, a reliable manufacturer, suitable material, sensible pack quantity, and consistent stock availability. Electricians value consistent sizing across the Clipsal 564PC range and bulk pack quantities that match a typical day's rough-in work. Avoid generic unbranded clips for jobs where consistent fit and finish matter.
Different cable fixings suit different cable types, surfaces, and environments. Use this comparison to confirm whether brass pin clips are the right choice or whether another fixing is needed.
Plastic cable clips often suit indoor flat TPS cable runs, particularly for fixed wiring inside wall cavities and behind plasterboard. They are inexpensive and quick to install. Brass pin clips are better aligned with round cable fixing on timber where corrosion resistance and a tidy visible appearance matter. Plastic can become brittle in hot roof voids over many years; brass does not behave the same way.
Stainless steel saddles and stainless cable ties offer stronger corrosion resistance in marine, coastal, or harsh exposed environments. Brass sits between plastic and stainless steel. It is a practical middle ground for many timber-fixed cable runs. Use stainless steel where direct salt exposure, regular wetting, or aggressive chemical exposure is expected. Use brass where the environment is indoor, sheltered, or only mildly damp.
Brass pin clips are not the correct fixing for conduit. Conduit must be supported with conduit saddles or compliant conduit clips designed for the conduit diameter. Sparky Direct stocks conduit saddles in full and half profiles, plus dedicated PVC conduit clip saddles for plastic conduit runs. For the wider conduit support range, see electrical conduits and fittings.
Common mistake: Using brass pin clips on PVC or metal conduit. The clip is sized for cable, not conduit. The fixing is not compliant for conduit support and can damage the conduit. Use the correct conduit saddle for the diameter.
Heavier cables, bundled runs, armoured cable, conduit, cable tray, and open-air spans need different fixing systems. Use full saddles or half saddles for conduit and heavier cables. Use cable ties for bundling and securing groups of cables. Use cable glands where a cable enters an enclosure. Match the fixing to both the cable and the surface.
This section gives practical use-case guidance to reduce returns and prevent unsafe substitutions. Confirm the cable, the surface, and the environment before placing an order.
Brass pin clips suit round flexible cables, light-duty multi-core round cables, and many common single round cables used in residential and light commercial cable support. They work well in ceiling spaces, on roof timbers, in sub-floors, on skirting and architrave runs, and on exposed timber framing in renovation and visible-run applications. Always confirm cable type compatibility before selecting brass pin clips for the job.
The integral pin is designed for timber. It suits joists, rafters, studs, skirting, and timber framing. Masonry, plasterboard, steel framing, composite sheets, and fragile or hollow surfaces require a different fixing. Driving a brass pin clip into masonry will bend the pin or shatter the surface. Driving it into thin steel framing will not produce a secure fix.
Brass pin clips also suit tidy cable retention near pendant fittings, surface-mounted luminaires, exposed timber feature work, and renovation touch-ups where the work remains compliant. The clip's low profile and brass finish keep visible runs tidy. Any electrical work must be completed by a licensed electrician where required by law.
Online buying is faster than a trip to the wholesaler when you have the right size and quantity confirmed in advance. The framework below converts research intent into a clean buying decision.
Best value comes from the right size, the right pack quantity, a trusted brand, reduced rework, and having enough clips on hand to finish the job. The cheapest clip is not always best. A poor fit can compress insulation, allow movement, or fail at inspection. Trade pack quantities of 200 generally suit a steady run of residential and light commercial work without forcing a return order.
Sole traders and small electrical contractors often buy multiple clip sizes for repeat use. Carrying a full set of Clipsal 564PC sizes in the van avoids substitution errors and keeps rough-in work moving. Bulk ordering also reduces supply interruptions and supports project planning across multiple jobs running in parallel.
Price-sensitive buyers should still match clip size to cable, confirm the substrate, and stick with a known manufacturer such as Clipsal. Affordability is a sensible factor in trade purchasing. It is not a reason to compromise correct specification or compliant use. The cost of a callback or rework outweighs any small saving on the clip itself.
Look for clear product sizing, pack quantity transparency, compatible cable information, delivery options, and GST-inclusive pricing where relevant. An online electrical wholesaler should make size comparison easy and stock the full range so a single order covers the job. Sparky Direct is set up for trade-friendly online ordering across the full Clipsal 564PC brass pin clip range.
For urgent purchase, check stock status on the relevant size, confirm the available delivery options, and review the pack quantity before ordering. Confirm the order covers all sizes the job needs in one transaction. Consider any related accessories at the same time, such as cable ties or saddles, to avoid a second order during the rough-in.
This section gives compliance-aware guidance rather than DIY installation steps. Electrical installation work must be performed by a licensed electrician where legally required in Australia. The notes below help buyers understand the standards and risks involved.
Electrical wiring and cable fixing as part of an electrical installation must be carried out by a licensed electrician where required by Australian state or territory law. Homeowners may purchase parts. They should not perform restricted electrical work themselves. The compliance and inspection process exists to protect property and life, and licensed work is part of that process.
Cable supports must prevent sagging, mechanical strain, abrasion, and damage to insulation. AS/NZS 3000 sets the framework for cable support in Australian electrical installations. The specific support spacing, fixing method, and clip selection depend on cable type, route, load, manufacturer instructions, and installation conditions. Refer to the standard and to the manufacturer data for any specific job.
Frequent mistakes include undersized clips that compress insulation and oversized clips that allow movement. Other errors include over-driving that splits the timber, fixing into unsuitable substrate, attempting to use clips on conduit, and applying clips to flat TPS where a flat clip suits better. Using brass in environments where stainless steel is required is also a common mistake. Each error can lead to cable movement, insulation damage, failed inspection, rework, or reduced service life.
During inspection the cable support, the intact insulation, the correct fixing method, and the suitable substrate all matter. Correct clip selection supports professional workmanship and reduces callbacks. A neat, correctly sized clip run on timber gives a tidy finish that holds up across inspection and the warranty period.
Reviews and brand comparisons help buyers compare suppliers and product ranges. The notes below cover what to evaluate and how to read review information sensibly.
Rating factors that matter for trade buyers include correct size availability across the full range, brand reliability, brass material quality, pack quantity, fit-for-purpose performance, and consistent stock. The Clipsal 564PC range scores well across these factors. Customer reviews on the Sparky Direct product listings provide additional buyer perspective on actual job performance.
When reviewing the product listing, check size options shown, written specifications, current price, stock status, shipping information, and related accessories suggested. A clear listing reduces order errors. Read the customer reviews on the listing for first-hand notes from electricians and trade buyers who have used the clips on real jobs.
Useful comparison criteria are product size clarity, availability of the common Clipsal 564PC sizes, pack quantity transparency, delivery options, trade usability, and the depth of related cable fixing categories. A supplier that stocks brass pin clips alongside saddles, cable ties, conduit clips, and cable glands makes job planning faster and reduces split orders.
Club Clipsal is Australia's largest electrician community offering trade rewards, business support, and exclusive benefits. When you nominate Sparky Direct as your preferred wholesaler, we automatically apply your Clipsal spend points to your Club Clipsal account daily.
Entry-level offering coaching, mentoring, and training discounts
Unlock exclusive industry tools and networking events
Access Toyota fleet offers and business software discounts
Maximum benefits, including VIP experiences and rewards
1. Sign Up: Create your Club Clipsal account at clipsal.com/club-clipsal or via the iCat mobile app
2. Nominate Sparky Direct: Select Sparky Direct from the wholesaler dropdown menu in your profile
3. Add Email: Enter your Sparky Direct account email address in the membership number field
4. Start Earning: Every dollar spent on Clipsal products earns points automatically
Redeem points from the rewards store, including gift cards, tools, and experiences. Access business summits, product training, and industry networking events. Receive early access to new product launches and special promotions. Connect with fellow electricians via the Club Clipsal community app.
Watch Clipsal 564PC2 | Pin Clips Brass Number 2 (Pack of 200) video
Watch Clipsal 564PC3 | Pin Clips Brass Number 3 (Pack of 200) video
Watch Clipsal 564PC5 | Pin Clips Brass Number 5 (Pack of 200) video
Sparky Direct literally saved my Christmas display. We had used all of the metal clips from previous years, and still had 50 metres of rope lights still to put on the Christmas train. A quick trip to the 2 large hardware stores in the area resulted in strange looks. No one knew metal electric cable clips!! Search the web and there was Sparky Direct!! A quick phone call sorted the size I needed and the order was in. The clips were delivered the next morning. Thanks to the excellent product and Sparky Direct's incredible customer service the Christmas Train and the Sleigh were completed in time for the children of the neighbourhood to enjoy.
Excellent, used these to hold wiring loom on veteran car with wooden body, they will ultimately blend in.
As a regular buyer from Sparky, I go to them for those sometime hard to get items, post is always prompt, good supplier to us as rural customers, and their pricing is competitive, quality products have always been supplied.
Quality products in stock • Fast Australia-wide delivery • Competitive trade pricing
Browse Brass Pin Clips → Get Expert Advice →Yes, they are designed to sit close to the surface for a neat finish.
Sparky Direct supplies brass pin clips Australia-wide, offering reliable cable fixing solutions with convenient delivery.
They are securely packaged and delivered via standard courier services.
Unused products are generally eligible for return according to the seller’s returns policy.
Warranty coverage varies by manufacturer and typically relates to material quality.
Yes, brass pin clips are typically sold in packs of various quantities.
Yes, selecting the correct size ensures secure fixing without damaging cables.
Yes, they are commonly used for small repairs and tidy cable routing.
They can sometimes be painted, depending on the application and finish.
Yes, they are especially suitable for fixing into timber.
When the correct size is selected and installed properly, they should not damage cables.
Yes, their discreet design makes them suitable for visible installations.
Yes, they are commonly used for light-duty cable management.
Brass pin clips are small fixing components made from brass, designed to secure cables, wires, or light fittings to surfaces.
They are straightforward for licensed professionals to install using appropriate tools.
Brass pin clips offer a more traditional appearance and strong fixing into timber surfaces.
Yes, they offer a tidy and discreet way to secure cables.
They are generally intended for permanent fixing and are not usually reusable once installed.
Yes, they are available in various sizes to suit different cable diameters.
They may be used outdoors in sheltered environments, but corrosion resistance should be considered.
Yes, they are commonly used indoors for neat cable fixing.
They are suitable for holding small, light-duty cables, depending on the clip size.
Quality brass pin clips are manufactured to meet relevant material and safety expectations when used as intended.
Yes, they are widely used for light-duty electrical cable management when installed correctly.
They are commonly used to fix electrical cables neatly along walls, skirting boards, or timber surfaces.
